PulseGuard Pulsation-Dampeners.com
Index | Selection / Quotation (What do you need?) | Contact Information

Pulsation Dampeners | Please Phone 910-270-2737 | We have people not voicemail | Call toll free 1-888-326-7377
Fluid Flow Control Animations
Fluid Flow Control Animations

Pulsation Dampeners - Acceleration Head / Pressure that a System Could Create

Consider suction acceleration head ("A.H.") losses, + how much discharge "A.H." your system will generate. estimate, how smooth it will be, with no dampeners at all. Before specifying a smoother system, you may wish to estimate how much improvement you need from the system, as it will be. The calculation below is a rule of thumb that converse pressure pulsation generated to overcome system resistance to pump flow fluctuation only.

Explanation:
Pressure pulsation generated by a system resisting flow fluctuation from your pump mostly depends on the mass of your liquid that has to follow the variations in velocity from your pump, the "flow fluctuations". This need to create head, or pressure, is often referred to as system "mass acceleration head". Flow "friction" also plays a part (see friction page) depending on system pipe size choice. To "visualize" what has happen, first establish the weight of you liquid that has to fluctuate. Then consider the speed at which you intend to run your pump. The mass and time available for velocity change is where your system generates the pressure pulsation excitation. How much this is dissipated or amplified by the characteristics of your piping design, controls how much pulsation your system will cause.

Necessary information to estimate acceleration head pulsation:
SG Specific Gravity - Grams per Cubic Centimeter gm/"cc" gm/cm3 Conversion from Lbs/Ft3, divide by 63 L Length of pipe in feet, Ft. Q Volumetric flow rate, in US Gallons per hour. Consider 1 US Gallon to equal 3.8 Liters N Number of displacements per minute. RPM x Number of displacers per rev. ID Average Internal Diameter of the pipe that is full of the liquid. Z A figure of relative decrease in "pulsatiousness" by number of displacers - examples are crank driven plungers. NOTE: SG, L & ID have nothing to do with the pump.

Relationship:
Addition to system pressure, peaks from accelerated head. or on a suction supply system: the pressure loss that will prevent the pump from filling.

Pulsation Dampeners - Dampening Equasion

 

Typical valves for "Z" for reciprocating sine motion driven machines:
1 For simplex (Single piston, plunger, or maybe reciprocating oil to move a diaphragm.)
2 For duplex (Two plungers, etc. Flow still comes to a halt as one displacer takes over from the other.)
4 For triplex (Three plungers etc. Flow still comes to a near halt unless the volumetric efficiency is well above 75%.)
6.5 For quadruplex (Four plungers etc. phased at 90 - -Sounds better, but chances of resonance are worse.)
9 For Quintuplex (Five displacers, overlap even with hot compressible liquids at high pressure.)
18 For Septuplex (seven displacers, smoother flow than a "Quin", but the frequency is high and may match the natural vibration frequencies or the acoustic or the mass oscillation frequencies of short pipe nodes)

For two displacers or more where the drive is a linear oscillation, for fluid power, the value for "Z" may be more than doubled. How much more than doubled, depends on the dwell that occurs on direction changeover. This is more affected by drive fluid compressibility than valve design.

Two Examples:
In these TWO EXAMPLES, the pumped flow rate, stays the same, the "jerk-rate" - number of modulations per minute, and everything else stay the same, EXCEPT PIP LENGTH " L".

Pulsation Dampeners - Dampening Equasion Pulsation Dampeners - Dampening Equasion

The formula is from general industry use by Milton Roy and Foster Wheeler etc. The "Z" factors are modified from empirical experience since 1963.

Note:
Increased pipe length gives more pulsation. Therefore, pulsation depends on the system. Similarly, changing the density of the liquid, or the diameter of the pipe, will change the pulsation.

Note:
As pulsation depends on pipe system length, diameter and the specific gravity of the system liquid, determining a dampening need without taking system details into consideration, is likely to lead to a less than suitable specification.

PUMPS make FLOW, - BUT- SYSTEMS make PRESSURE, PRESSURE PULSATION is a system response to flow fluctuation, and a SYSTEM RESPONSIBILITY, not a pump vendor liability - not is the pump vendor necessarily qualified to address system piping and valve response pressure pulsation. Please call 1-888-DAMPERS, not the pump vendor.

Liquid Dynamics Pulsation Dampeners Information For more information about this and other pressure pulsation related topics go to the Liquid Dynamics web site

Pulsation Dampeners - Snubbing, Surge Suppression and Shock Absorbing
Hydropneumatic Device for Pulsation / System Acceleration Head Loss Prevention
No Moving Parts and Hydropneumatic Pulsation Filters
Flow Fluctuation / Suction Systems - Negative Pressure Pulsation / Supply Lines
Pressure Pulsation Pulse Signatures
Pressure Pulsation Dampeners for Transients and their Interception
Pulsation Dampeners for Amplitude of Pressure Wave Spikes
Pulsation Dampeners and Pump Vendor Responsibilities
Acceleration Head / Pressure that a System Could Create
Pulsation Dampening - Flow Smoothness Requirements
Pulsation Dampener Quick Release Manifolds / Flow Divider Manifolds



Pulsation-Dampeners.com
Index | Selection / Quotation (What do you need?) | Contact Information

Click on the picture of the damper below to see how it works and is assembled, animated.
HP Liquid in Bladder Pulsation Dampers Gas Bladder Pulse Dampers / Accumulators LP Elastomer Membrane Surge Suppressors LP PTFE Diaphragm Pulse Dampeners HP PTFE Membrane Pulsation Dampeners Sludge Slurry Flexible Tube Dampners Pressure Pulsation Pulse Frequency / Frequencies

Fluid Flow Control Fluid-Flow-Control.com The Fluid Flow Control Source Pumps Accumulators Filters Dampers Heat Exchangers Valves Mixers P.I. / Pressure Indicators Controls Meters Vessels